input parameter conditions min. typ. max. units input voltage range universal 85 264 vac 127 373 vdc input frequency 47 63 hz input filter meets en 55022 class b input current see model selection guide inrush current cold start, 115 vac 25.0 a pk cold start, 230 vac 40.0 safety ground leakage current 264 vac 0.25 ma output parameter conditions min. typ. max. units output voltage/current see model selection guide output voltage tolerance see note 1 ?.0 % line regulation vin = 100 vac to 240 vac ?.5 % load regulation iout = 10% to 100% ?.0 % ripple & noise (20 mhz) see note 2 ?.0 % hold-up time 115 vac 8 msec 230 vac 60 temperature coef cient ?.05 %/? short circuit protection continuous (autorecovery) overload protection 170 % general parameter conditions min. typ. max. units isolation voltage input to output 3,000 vac isolation resistance 500 vdc 100 m isolation capacitance 1,100 pf emi/rfi conducted en 55022; en 61000-3-2, -3 emc compliance electrostatic discharge (esd) iec/en 61000-4-2, -6, -8, -11 rf field susceptibility iec/en 61000-4-3 electrical fast transients/bursts on mains iec/en 61000-4-4 surge iec/en 61000-4-5 switching frequency fixed 66 khz environmental parameter conditions min. typ. max. units operating temperature range ambient 0 +25 +70 ? storage temperature range -20 +85 ? cooling free air convection (see derating curve) humidity rh, non-condensing 93 % physical size 2.16 x 1.378 x 0.827 inches (55.0 x 35.0 x 21.0 mm) weight 1.23 oz (0.035 kg) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 200 khours safety standards ul 60950, en 60950 vibration sinusoidal 50~500 hz, 3.0 grms, period of 30 min each along x, y & z axis miniature pcb-mount, 5w, open frame ac/dc power supplies key features: 5w output power universal 85-264 ac input en 60950 approved (ul) pcb mountable meets iec safety class ii meets en 55022 b ef ciency to 80% >200 khour mtbf mpb-05s series electrical speci cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com
model selection guide mechanical dimensions derating curve notes: 1. output voltage tolerance is measured at nominal input and 75% load. 2. output ripple is measured at 20 mhz bandwidth using 0.1 f and 10 f capacitors connected in parallel as close to the power supply terminals as possible. 3. these units will operate at no load without damage. for most applica- tions however, mpd recommends that a minimum load always be used. contact the factory for more information. 4. each unit includes an input fuse (250v/1a). since this fuse is not eld replaceable, it is recommended that an external fuse of the same size be used on the input of the power supply for protection. notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.02 ( 0.50) micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com other models may be available. contact the factory for details www.micropowerdirect.com model number input output max output power (w) ef ciency (%, typ) current (a) voltage (vdc) current (a) 115 vac 230 vac rated % min. MPB-05S-03 0.15 0.07 3.3 1.25 0.00 4.12 70 mpb-05s-05 0.15 0.07 5.0 1.00 0.00 5.00 73 mpb-05s-09 0.15 0.07 9.0 0.55 0.00 5.00 76 mpb-05s-12 0.15 0.07 12.0 0.42 0.00 5.00 77 mpb-05s-15 0.15 0.07 15.0 0.33 0.00 5.00 78 mpb-05s-18 0.15 0.07 18.0 0.28 0.00 5.00 78 mpb-05s-24 0.15 0.07 24.0 0.23 0.00 5.50 80 pin description 1 ac-neutral 2 ac-line 3 -v output 4 +v output pin connections
|
